kb.paessler.com
Welcome to the Paessler Knowledge Base Archive. Here, you will find articles from kb.paessler.com.Please note that this is a mere import of all questions and the corresponding replies into a new platform. The important articles were transfered manually - articles in this folder were imported automatically. We tried to keep links working, but some may fail. If you find some, please let us know. Please bear in mind that articles in this folder may contain old / outdated data.
Moin,
ein Kunde möchte zukünftig sein Monitoring mit eigener Lizenz selber betrieben.
Im Rahmen eines kleinen Projektes soll dessen PRTG-Umgebung auf seinen Core umziehen.
Ich habe den "How can I move (migrate) my PRTG installation t...
Tue, 10 Jun, 2025 at 10:34 PM
I've recently replaced my cisco 3750 switches with Cisco 3850, and now PRTG won't detect Port-Channels, has anyone come across this?
Article Comments
The Port-Channel is a proprietary technology from Cisco, different ven...
Tue, 10 Jun, 2025 at 10:34 PM
Hi,
I would like monitor Exchange infrastructure 5 MB server / 3 CAS / 2 EDGE
-Current unique users (OWA) /
-RPC Connection /
-Sent, delivered email
I will use WMI Exchange Server but wher...
Tue, 10 Jun, 2025 at 10:34 PM
Good day.
I am using PRTG since long time. And i want to create a user for my PRTG only monitoring. The can't change any think. he just monitor the prtg. is that possible?. plz help me. give me the solution.
Article Comments ...
Tue, 10 Jun, 2025 at 10:34 PM
Hello everyone,
I have installed PRTG and in the remote side on a Raspberry pi installed miniprobe which is working fine but the Raspberry pi is connected to a router and I want to have the snmp information of that router and due to some ...
Tue, 10 Jun, 2025 at 10:34 PM
I'm trying to monitor the avarage response time for the HTTP Advanced Sensor. HTTP Sensor interval is currently set 60 seconds, I would like to configure a sensor which checks the avarage value of the last 5 reading of the HTTP sensor....
Tue, 10 Jun, 2025 at 10:34 PM
How can I configure PRTG to alert when an interface/port on a switch goes down?
Regards,
Article Comments
Hi there,
You can enable the "Connection Status Handling > Show alarm for all "disconnected" states&...
Tue, 10 Jun, 2025 at 10:34 PM
Hi all
I am trying to configure a SSH Remote Ping sensor but when the sensor is deployed I am receiving the following error message,
Socket error on connecting. WSAGetLastError return 10061($274D) No connection could be made because the...
Tue, 10 Jun, 2025 at 10:34 PM
I get the following error when attempting to add the Hyper-v virtual machine sensor to a host:
8004100E: The namespace specified could not be found.
I have confirmed that UAC is disabled and I have rebuilt the wbem files.
Articl...
Tue, 10 Jun, 2025 at 10:34 PM
I am using Microsoft SQL v2 BETA with "Process data table" and "Difference" options switched on.
I have two consecutive readouts from SQL like
20.01.16 19:49:28 Id 3 return 1537 [Int64]
20.01.16 19:50:28 Id 3 re...
Tue, 10 Jun, 2025 at 10:34 PM
These objects, server vms on an esxi host, all used to work at one point. Recently I began receiving a down status with the message, "Input string was not in a correct format." I have tried deleting and recreating the objects, but...
Tue, 10 Jun, 2025 at 10:34 PM
Can you add a scroll down option for devices->group view menu?
In newest version I can see only twenty remote probe in this menu
Article Comments
Hello,
Displaying of "Devices -> Group View" has been same for ...
Tue, 10 Jun, 2025 at 10:34 PM
I have successfully setup File Content sensors in the past and have used the same method in this case. However, I was not getting a consistent result and now I am getting an incorrect result all of the time. The problem does not seem to be ...
Tue, 10 Jun, 2025 at 10:34 PM
Hi,
I've got a java application running on tomcat where I've got an agent implementation using snmp4j which is very simple and is similar to the one here http://www.jayway.com/2010/05/21/introduction-to-snmp4j/. Just a normal mib ...
Tue, 10 Jun, 2025 at 10:34 PM
Hello,
I cannot add SNMP sensors for Cisco Meraki MX series to PRTG. The only information that I found at PRTG forum was related to Cisco Meraki Access Points but nothing about the MX series.
I have tried to import the MIB file to the PRTG...
Tue, 10 Jun, 2025 at 10:34 PM
I have created some custom sensor table map objects, to display simple lists of sensors. I have the following poperties in my map object code:
columns="sensor, lastvalue, minigraph"
sortby=""
sortable="true" ...
Tue, 10 Jun, 2025 at 10:34 PM
I used portsensor, httpsensor, ping, each one failes with timed out/down, but the camera is working perfectly, I configured it with a static ip, this only happens to the cameras i got every other device and my server works fine no issue at ...
Tue, 10 Jun, 2025 at 10:34 PM
Dear Paessler team,
I just re-install my Windows due to HDD crash, to a new HDD. After I re-install PRTG Network Monitor, and tried activate, it said that "Current activation status of your software license : Activation grace period ...
Tue, 10 Jun, 2025 at 10:34 PM
Hello everyone, I would like to know how can I add a new folder to the Map Designer on the right side. I would like to create a new folder where I would be able to put all my icons in it.
I saw that topic talking about that feature, but no ...
Tue, 10 Jun, 2025 at 10:34 PM
Hello,
About 4 month ago I enable Netflow on our virtual infrastructure. I am now looking at enabling Netflow v9 on our core network stack. In trying to estimate the effect on our PRTG server resources, I need to know how long does PRTG (b...
Tue, 10 Jun, 2025 at 10:34 PM
I've used the KB article detailing how to create F temp sensors from C sensors using Sensor Factory sensors.
https://helpdesk.paessler.com/en/support/solutions/articles/8453-celsius-to-fahrenheit
However, it pulls the units from the p...
Tue, 10 Jun, 2025 at 10:33 PM
Hello
I am trying to parse the total data used in a specific month (for billing purposes).
From what i've read, the historicdata should be able to offer me that.
My request is: http://monitor:8080/api/historicdata.json?username=user...
Tue, 10 Jun, 2025 at 10:33 PM
Hello support team!
I just installed current version of PRTG, at first glance all looks fine, but I'm found that I'm unable to create any of .Net-related sensors - its grayed out and unable to be added to device.
My OS are WinSe...
Tue, 10 Jun, 2025 at 10:33 PM
Dear Sirs,
how can monitor health situation for this V1920 switch only?
are there some probes/sensor for this kind of switch?
i looking for mib in the vendor site but there is a millions of it ... do you have any example to configure ...
Tue, 10 Jun, 2025 at 10:33 PM
Hi Everyone,
I am having a challenge enabling SNMP communications between a Virtual Machine (called 'NetMon', see diagram), and a Hyper Visor / Host (called 'PA-SERVER03', see diagram). Both the VM and the Host use the Win...
Tue, 10 Jun, 2025 at 10:33 PM
Hallo zusammen,
ich würde gerne entsprechend der Empfehlungen (Für optimales Monitoring mit PRTG empfehlen wir Microsoft Windows Server 2012 R2 oder neuer für den PRTG Core Service und Probe Service.) von PRTG meine Installation auf eine...
Tue, 10 Jun, 2025 at 10:33 PM
I would like Placeholders made for:
Upper Warning Limit [unit] = %UpperWarningLimit
Lower Warning Limit [unit] = %LowerWarningLimit
Currently, this is my setup.
In one of the Sensor Comment Sections I but the following (values do chang...
Tue, 10 Jun, 2025 at 10:33 PM
Hi all,
I am newbie to thi PRTG tool. When receiving notifications from Servers, it receives notifications on event logs.
I would like to omit certain event logs from the notification. Currently logs filter dropdown showing with options...
Tue, 10 Jun, 2025 at 10:33 PM
Hi, Has anyone had any success in configuring temperature control for a Climate CM-2.
I've imported the MIBs and added some sensors but they constantly error.
Thanks
Article Comments
Hi Chris,
Which sensors have you tri...
Tue, 10 Jun, 2025 at 10:33 PM
Hi,
I have a problem with PS script that is checking if port on remote host is open or not. I'm executing this script with Custom EXE/Script sensor and it is working but always giving the 1:ERROR value, below you will find the code :...
Tue, 10 Jun, 2025 at 10:33 PM
Hi,
How do I generate a report similar to Top Talkers report where it displays the top IP addresses that are utilizing our bandwidth but I need it based on Date range (from-to). The bytes should be the total base on the date range that I ...
Tue, 10 Jun, 2025 at 10:33 PM
How can I set a DNS sensor to norecurse? The issue I'm finding is authoritative DNS servers are starting to get updated to not allow recursive DNS requests.
A real DNS server wouldn't make a recursive request, so this is a secu...
Tue, 10 Jun, 2025 at 10:33 PM
Dear,
This is probably a stupid question...
I recently added an IP temperature/humidity sensor to my PRTG config over SNMP.
In the device overview, I have 3 sensor for this device. (Uptime, Temperature and Humidity)
Both Temperature and...
Tue, 10 Jun, 2025 at 10:33 PM
Hi @all,
I´m trying to implement our IBM BladeCenter H into PRTG with Problems. The MIB is out of the actual AMM Firmware (bpet66p), AMM is also up-to-date.
I imported the partial MIB with MIB importer to "\snmplibs", added a ...
Tue, 10 Jun, 2025 at 10:33 PM
A config change to a Brocade switch was recently made to add two new logical switches (for a total of 3).
Since the change, the only ports in PRTG that show as 'up' are those still in the native fabric; ports in the two new fabri...
Tue, 10 Jun, 2025 at 10:33 PM
I would like to hide graphs which are displayed on the right side of the screen.
But I don't know how to do it.
Do I have to modify something in HTML/CSS code ?
Thanks for your answer.
Article Comments
Yes, you may cus...
Tue, 10 Jun, 2025 at 10:33 PM
I upgraded our 3 server DAG from Exchange 2013 CU9 to CU11 this past weekend. After doing so, some of the DAG Powershell sensors return an error. Deleting the sensor, restarting PRTG and redeploying the sensor doesn't clear the error.
...
Tue, 10 Jun, 2025 at 10:33 PM
Hello,
i got a problem. I have to use my own icons.
The Problem now is that they can't be dynamic (Counts the sensors which are critical/ warning/ good) in the folder iconset 7+ 8.
Is there any way to have this own icons in theses fo...
Tue, 10 Jun, 2025 at 10:33 PM
I need to be able to monitor Windows PC's which are not directly accessible, but through VPN Port 5900 within another local Subnet (192.168.1.xx). Can this be done with an agent, probe?
thanks, Clem
Article Comments
Hello Th...
Tue, 10 Jun, 2025 at 10:33 PM
Hi,
we are running PRTG 14.1.8.1371 stable with a vmware vCenter 5.5. We use the SOAP Sensor for monitoring it.
Today we got a problem on the connected hosts that told us problems with statistics data.
Over vmware support we came to the e...
Tue, 10 Jun, 2025 at 10:33 PM
You can see my troubleshooting steps here:
https://www.reddit.com/r/sysadmin/comments/438v7w/prtg_network_monitoring_problems/
Currently I'm getting this SSH error:
The host's system is unable to process PRTG's command: "...
Tue, 10 Jun, 2025 at 10:33 PM
Hello
First : sory for my bad english
Second : Prtg network monitor is super, amazing good software !
Im using smtp senzor for measure temperature.
Until yesterday everything was fine until the outside temperature fell down to zero degree...
Tue, 10 Jun, 2025 at 10:33 PM
After monitoring VMware with PRTG, the database of vmware vcenter is crashing because of login / logoff events written by PRTG.
The database crashes because of the 10g limit in the express version.
Every login is been protocolled. In 15...
Tue, 10 Jun, 2025 at 10:33 PM
Kind PRTG users,
i am trying to build a script to show me the enabled users in a active directory. i use the following command: (get-aduser -filter *|where {$_.enabled -eq "True"}).count this wil give me a value like 178. But wh...
Tue, 10 Jun, 2025 at 10:33 PM
I want this sensor to alarm when the traffic goes under 20,000 kbits/second. Please advise.
Article Comments
Hi,
you can use channel limits here to set the sensor to error when a certain limit (upper or lower is reached).
Best...
Tue, 10 Jun, 2025 at 10:33 PM
I have PRTG with managed switch ports, and rely on SNMP traffic in/out counters for my wired users. I need similar data for my wifi users. I am able to apply static wifi DHCP assignments, and I am willing to purchase all new access points...
Tue, 10 Jun, 2025 at 10:33 PM
I use <our prtg server name> /api/table.xml?content=sensors&columns=objid,probe,group,device,sensor,type,status,comments&count=50000'
Exporting sensor information to xml is a great way to check if all settings are accord...
Tue, 10 Jun, 2025 at 10:33 PM
I have a Cisco modem that supports IPSLA. Can PRTG check if the internet connection is still up and running?
Article Comments
This can be done using the Cisco IP SLA sensor with the following configuration on the device itself....
Tue, 10 Jun, 2025 at 10:33 PM
We're using HTTP Advanced sensors to periodically test available bandwidth to multiple hosts (as per https://www.paessler.com/network_bandwidth_test). Is it possible to ensure the tests will not be run at the same time? Otherwise the re...
Tue, 10 Jun, 2025 at 10:33 PM
I use PRTG syslog server, and I received many notification messages as
"/usr/sbin/cron[31745]: %CRON-6: (root) CMD (newsyslog)"
It's difficult for me to monitor needed messages.
How can I remove those.
The configuratio...
Tue, 10 Jun, 2025 at 10:32 PM
Hi All,
I have installed and configured PRTG Network monitor on a VM (which is running through Microsoft Hyper-V).
When I performed the initial installation I configured the 'primary probe' on the loopback I.P. address of 127.0....
Tue, 10 Jun, 2025 at 10:32 PM
We currently have a core server hosted externally, which we want to replace with an internal one.
It has local probe, cluster probe, a remote probe under our control and several remote probes under the control of clients.
So, unfortunat...
Tue, 10 Jun, 2025 at 10:32 PM
I have the green light to purchase this software but I would like to have a better understanding of how to implement the software and the associated sensors before doing so. I currently have prtg installed on a hyper-v vm and get the basic ...
Tue, 10 Jun, 2025 at 10:32 PM
How i can use Netflow V9 to monitor the upload and the download separately (for each user) on a sing
I tried to use SNMP but it gives me the total traffic not for specific users.
Article Comments
Hi Firas
You have to keep in mind that the ASA cannot differ between users, how should it. Thats only possible with a proxy on whic...
Tue, 10 Jun, 2025 at 10:32 PM
How can I programmatically, via PowerShell or some other scripting language, disable alerts or set up maintenance windows for devices? When I patch my servers, I want to disable the alerts for, say, 15 minutes before I run the patches. ...
Tue, 10 Jun, 2025 at 10:32 PM
I am looking for a way to pause and restart PRTG sensors during system patching or other maintenance, as part of automated script. I could not find any related reference, if it is possible.
Thanks in advance.
DJ
Article Comments...
Tue, 10 Jun, 2025 at 10:32 PM
hi,
i´ve tried to use the following KB Solution for a differt Version of an EMCdevice:
https://helpdesk.paessler.com/en/support/solutions/articles/26423-emc-storage-array
Unfortunately, I am not able to access the EMC Information with t...
Tue, 10 Jun, 2025 at 10:32 PM
Data has been captured and monitored till 20th Feb , but not it has stopped working.
Cisco Switch is sending data to PRTG but prtg is not showing the data.
Top talker and top connection is not showing in netflow sensor while other things ar...
Tue, 10 Jun, 2025 at 10:32 PM
So I created the custom SSH sensor, and in data type I've set it as integer.
When being graphed with 30m periods and higher, it shows values like "Max 24.2"
It is not what I expect to see as a value for "integer"...
Tue, 10 Jun, 2025 at 10:32 PM
Hi.
I have added the wmi event log sensor, and it gives all the events that happens. But what i want that it also gives the message's itself not only the number of events that happen.
Is there a solution for my problem?
Kind regar...
Tue, 10 Jun, 2025 at 10:32 PM
Hello,
How can i monitor FreePBX 12?
I need monitor trunks load (simultaneous calls on each trunk).
Article Comments
Doable easily IMHO.
You can write File Sensor or File Content Sensor that keeps on monitoring output of a bas...
Tue, 10 Jun, 2025 at 10:32 PM
We are currently migrating our database servers to RDS in Amazon. I am interested how I can utilize PRTG to monitor this instance. Particularly wanting to understand how I can monitor for success/failure of backups. Any guidance apprecia...
Tue, 10 Jun, 2025 at 10:32 PM
I'm trying to retrieve all the "tags" for a specific object but it doesn't seem like getobjectproperty has a version for json. I can do regex matching for the html, but I was hoping there was a cleaner solution.
Ar...
Tue, 10 Jun, 2025 at 10:32 PM
Good Day,
Looking to monitor Galera cluster. Running the SQL query:
SHOW STATUS LIKE 'wsrep_cluster_status'
It returns:
Variable_name Value
wsrep_cluster_status Primary
I am looking t...
Tue, 10 Jun, 2025 at 10:32 PM
I parametered sensor (ntpd) for linux. It goes well in the console but when I stop the service on the linux the sensor does not change state.
OS : debian 8
Prtg : 16.1.22.2391
Article Comments
I resolve my problem
Mar, 2...
Tue, 10 Jun, 2025 at 10:32 PM
Hello,
I would like to increase the font size of the icons in the maps.
For exemple, i would like to increase the font size of the icons A.
But I don't want a bigger logo.
Is it possible ?
I use the PRTG v15.
Thanks.
Artic...
Tue, 10 Jun, 2025 at 10:32 PM
Previous PRTG versions provided the SNMP GSA System Health sensor to monitor the health of my Google Search Appliance. This sensor type is marked as “deprecated“ as of version 16.x.23 and removed from PRTG with version 16.x.25.
Is there a...
Tue, 10 Jun, 2025 at 10:32 PM
I use PRTG IMAP Sensor for a few Backupmails. Now I have the problem that it does not find any email in the mailbox which has () or [] in the subject. I tried with string search and regular expression.
Could that be a problem? If I configur...
Tue, 10 Jun, 2025 at 10:32 PM
Hi,
i tried to install the demo version on a Windows 7 PC. But the core Server service is not starting.
PRTG Version is 16.1.22.2391
Error message:
Signature of C:\Program Files(x86)\ PRTG Network Monitor\PRTG Server.exe is not vaild...
Tue, 10 Jun, 2025 at 10:32 PM
Hi All,
I have tried to configure sensors with maintenance schedule, when the section "Schedules, Dependencies, and Maintenance Window" under sensor's setting tap is open, the "Save" button will have no response wh...
Tue, 10 Jun, 2025 at 10:32 PM
Hi
We would like to be able to group our probes, into logical units.
Use case we have clients with multiple sites, we would like to have a group called the "clientname" then the sites listed underneath.
Libraries are not an ...
Tue, 10 Jun, 2025 at 10:32 PM
I'm trying to monitor bandwidth usage of a VPS running Windows Server 2012 R2 using the Windows Network Card sensor. This sensor worked fine on a dedicated server we had in the past, but on the VPS it only measures Packets (volume) and ...
Tue, 10 Jun, 2025 at 10:32 PM
I have tried several times to install PRTG on a Win7 PC and I am now using release 15.3.19.
After starting the install, I get a PRTG Start window that says - Please wait until PRTG's web server is running .... and a little later I see...
Tue, 10 Jun, 2025 at 10:32 PM
Hi,
When monitoring traffic utilization for a link in percentage, should I enter double the actual value of the link in the field Maximum (kbit/s). For example, for a 200Mb/s link should I enter 400000 kbit/s? The channels I am using are...
Tue, 10 Jun, 2025 at 10:32 PM
We have a NetApp cDOT I/O sensor that was working fine, then over the weekend started giving the error:
"Value was either too large or too small for an Int32"
Has anyone seen this? Not sure what to do. Opened a support ticket...
Tue, 10 Jun, 2025 at 10:32 PM
Greetings,
I have written a powershell script that is getting executed successfully whenever I am "testing" it from Setup > Account Settings > Notifications > Test from prtgadmin account.
However, I want it to get exe...
Tue, 10 Jun, 2025 at 10:32 PM
I have WMI ports and other suggest ports open on the local network on the firewall and remote prob workstation (windows 7). I also have the same ports open on the cloud firewall where the PRTG server is hosted.
I've even done these s...
Tue, 10 Jun, 2025 at 10:32 PM
Hello,
how can i see both incoming and outgoing traffic ( like in https://cdn.paessler.com/media/scales/lightbox/common/files/screenshots/bandwidth-monitoring.png ). Have added regular Netflow v9 sensor, but it only shows a single graph.
Al...
Tue, 10 Jun, 2025 at 10:32 PM
I'm now using PRTG for about 1.5 years. Some weeks ago, something happened (on the probe device or the network in general) and since then, all my RDP sensors have permanent messages for "Unusual 1 hour average...".
I know f...
Tue, 10 Jun, 2025 at 10:32 PM
Hello,
we are currently using the PRTG HTTP-request function to send sensor information to our database program, this is working fine.
The only problem is that i can't seem to use the PRTG placeholders together with the URL that i use...
Tue, 10 Jun, 2025 at 10:32 PM
Hello,
Currently i use email notifications in Text format.
Now i need some changes to default mail template.
But, when i set format to "Text with custom content", i see blank field (without default template).
How can i see Defau...
Tue, 10 Jun, 2025 at 10:32 PM
On top of our (and most people's probably) PRTG webpage there are 6 buttons with errors, down, warning, ok, paused and unusual (with numbers in them representing the amount of sensors in that state).
I would like to use this row of co...
Tue, 10 Jun, 2025 at 10:31 PM
Hello,
How can i monitor CPU usage in MHz (ESXi Host)?
Article Comments
Are you familiar with VMware's PowerCLI? With this it would be possible to solve this with a custom sensor.
Kind regards.
Mar, 2016 - Permalink
Tue, 10 Jun, 2025 at 10:31 PM
Hi,
i am running two VMware Hosts in Cluster mode. Both VMware Host show the the Hardware state directly on the Vcenter but only one of them show the results on the PRTG VMware Hardware Sensor.
The other one shows this warning message: ...
Tue, 10 Jun, 2025 at 10:31 PM
We have successfully added a set of icons to the \webroot\iconset7 and iconset8 but we would like to have different folder names to reflect the use of the icons on the map interface
rather than Icons Set 9 and Icons Set 10 -
For example w...
Tue, 10 Jun, 2025 at 10:31 PM
Hello!!
I need know... The PRTG can monitoring Web Aplications or just infrastruture?
Thank you for support!!!
Article Comments
Hello,
I think we can. Can you be more specific? What do you have in mind?
Feb, 2016 - Perm...
Tue, 10 Jun, 2025 at 10:31 PM
Hi All !
I am new here and my english is not very well.
I have one Windows Server 2012, I run script backup (robocopy) every day. Can I use thist sensor "EXE/Script Sensor" for run and monitoring the results?
Thanks
Luiz
...
Tue, 10 Jun, 2025 at 10:31 PM
this is the error message: "Please enter a valid class C network IP base (e.g. 192.168.0 )"
I have subnetted 10.200.0.0 and have remote sites in those subnets.
the tool wont let me create an autodiscovery group that references 10....
Tue, 10 Jun, 2025 at 10:31 PM
I'd like to create 1 sensor that represents the status of more then 1 probenode.
Eg is have multiple customers, all have installed 1 probe.
Now i'd like to create 1 sensor that tells me if there is an error at 1 of many probes so ...
Tue, 10 Jun, 2025 at 10:31 PM
Why is there a % representation on both sides of the graph? On the left it goes from 0 - 100%. On the right it's kind of a fluctuation between 0 and 10%.
Seems just one out of the 20+ processors are running at about 7%, which is corre...
Tue, 10 Jun, 2025 at 10:31 PM
Good morning
I am wondering if it is possible to use PRTG to check a journey through a website? By journey I mean get PRTG to log in to a site and run through approximately 20 steps (click on a button, enter a short text string, click a...
Tue, 10 Jun, 2025 at 10:31 PM
We have had PRTG (single server installation, server 2008R2) for a couple of years, and are showing maps through the ajax web interfaces (4-6 tabs pr monitor) on 4 monitors in our office. This setup has worked perfect for a couple of years,...
Tue, 10 Jun, 2025 at 10:31 PM
hi
i wanted to monitor tcp connections on specific ports so i created one ssh script which i kept in /var/prtg/scripts
scripts contents as follows
!/bin/bash
netstat -anp |egrep '(8081|8082|8083|8885)' |grep ESTABLISHED | aw...
Tue, 10 Jun, 2025 at 10:31 PM
Both PRTG Probe Service and PRTG Core Serrver Service is running.But prtg administrator can not login in no matter via prtg console and The browser .At this time service 80 port in state of listening. I Tried to restart the service. then pr...
Tue, 10 Jun, 2025 at 10:31 PM
Hi.
I've set up an API Event log sensor which monitors for a certain ID and has an upper limit of 0 so when ever a certain event occurs the sensor goes red with a DOWN status. Problem is that 60 seconds when a new scan has occurred it...
Tue, 10 Jun, 2025 at 10:31 PM
i have a couple different prtg installations where the 'overview' tab will randomly not load correctly when i click on a device or a sensor.
this behavior seems to have begun after the feb 2016 update.
it seems to do it about 20...
Tue, 10 Jun, 2025 at 10:31 PM
Hello,
We need to create a settings with a equal step of time between the graphs and equal number of values.
For example (10x step):
16 hours (1min) = 960 values;
7 days (10min Avg) = 1008 values;
70 days (2h Avg) = 840 values;
730 da...
Tue, 10 Jun, 2025 at 10:31 PM
I am getting this error,
page is working without any problems, but sensor shows. I try to pause and start again, nothing changed
it shows me on HTTP 1
what to do ?
Article Comments
Hello,
there seems to be an issue with...
Tue, 10 Jun, 2025 at 10:31 PM
Which views/tables from oracle database you using for this sensor.?
I need add proper grant select to user in database
Article Comments
Hello,
The user whose credentials are used needs to have permissions to log on to the sy...
Tue, 10 Jun, 2025 at 10:31 PM
Dear experts:
I want tap into the database to query events. I believe PRTG is using SQL lite. Is there a way to change the database to standard SQL?
Your help is much appreciated.
Best,
Jian
Article Comments
Hi Jian, ...
Tue, 10 Jun, 2025 at 10:31 PM
